index
会员中心 | English | 繁體中文
logo
首页 产品与标准 GJB 3372 (/36~/44) - 1998 100°开槽沉头螺钉

100°开槽沉头螺钉 GJB 3372 (/36~/44) - 1998

选择规格尺寸 点击↓

M3

M4

M5

M6

M8

M10

GJB 3372 (/36~/44) - 1998 100°开槽沉头螺钉

尺寸单位: mm
军标GJB 3372 (/36~/44) - 1998 GJB3372 3372 100°开槽沉头螺钉
GJB 3372 (/36~/44) - 1998 100°开槽沉头螺钉
扫一扫分享
公差 公制螺纹极限尺寸 米/英制螺纹对照 螺纹直径与受力截面积 最小破坏扭矩 牌号等级 毛坯直径
千件重及价格计算 千件重 : kg x 元/kg = 元/千件
默认密度 g/cm3
×

选择材料对应密度(g/cm3)

  • 碳钢 7.85
  • 不锈钢 8.1
  • 不锈钢 7.95
  • 不锈钢 7.7
  • 钛合金 4.5
  • 铝合金 2.8
  • 铜 8.89


在此选择或在计算页输入材料密度 密度表
公称长度L 注:选择后获得 相应重量
螺纹尺寸
d
M3 M4 M5 M6 M8 M10
H 参考
h 最小值
D 参考
D1 最小值
D2 供卡规设计用
r 最大值=公称
最小值
P2 最大值=公称
最小值
b 最小值=公称
最大值
t 最小值=公称
最大值
1.26 1.68 2.11 2.53 3.38 4.23
0.06 0.08 0.1 0.1 0.1 0.1
6 8 10 12 16 20
5.4 7.2 9 10.8 14.8 18.8
4.5 5.78 7.71 9 12.21 15.43
0.63 0.93 0.96 1.26 1.6 1.93
0.43 0.73 0.76 1.06 1.4 1.73
0.4 0.4 0.5 0.7 0.7 0.8
0.2 0.2 0.3 0.5 0.5 0.6
0.8 1 1.2 1.5 1.5 2
0.9 1.1 1.3 1.6 1.6 2.1
0.8 1 1 1.5 2 2.5
1.05 1.25 1.25 1.75 2.25 2.75
千件钢制重≈kg
- - - - - -
①,合金制螺钉理论质量，表中的钢螺钉理论质量乘以修正系数0.356。黄铜制螺钉理论质量，乘以修正系数1.1。

技术条件和引用标准

标准
GJB 3372/36
GJB 3372/37
GJB 3372/38
GJB 3372/39
GJB 3372/40
GJB 3372/41
GJB 3372/42
GJB 3372/43
GJB 3372/44
限用直径/mm 材料 热处理MPa /
表面处理		 标记示例：d=M6、L=36mm、C=3mm
1.6～10 ML25 镀锌钝化 GJB 3372/36 M6×36
4～10 38CrA σb=900~1100MPa
d≤M8 镀锌钝化，d=M10 镀镉钝化		 GJB 3372/37 M6×36
4～10 30CrMnSiA σb=1100~1280MPa
d≤M8 镀锌钝化，d=M10 镀镉钝化		 GJB 3372/38 M6×36
2～10 1Cr17Ni2 d≥M4, σb=1100~1280MPa
钝化		 GJB 3372/39 M6×36
5～10 GH 2132 σb≥900 GJB 3372/40 M6×36
1.6～3 1Cr18Ni9Ti / GJB 3372/41 M6×36
3～10 LY8 σb≥375
阳极化		 GJB 3372/42 M6×36
1.6～6 H62 钝化 GJB 3372/43 M6×36
1.6～6 H62 防磁 钝化 GJB 3372/44 M6×36

引用参考

GB /T 1172 - 1999
黑色金属硬度及强度换算值
GB /T 5267.1 - 2002
镀锌、镀镍、镀镉、复合镀等层镀层盐雾腐蚀的防护性能
GB /T 193 - 2003
普通螺纹（一般用途米制螺纹）- 直径与螺距系列 (ISO 261: 1998, MOD)
GB /T 3106 - 2016
紧固件 - 螺栓、螺钉和螺柱 - 公称长度和螺纹长度 (ISO 888:2012, MOD)
GB /T 3 - 1997
普通螺纹收尾、肩距、退刀槽和倒角 (ISO 3508:1976 / ISO 4755:1983)
GB /T 5779.1 - 2000
紧固件表面缺陷 - 螺栓、螺钉和螺柱 - 一般要求
GB /T 5779.3 - 2000
紧固件表面缺陷 - 螺栓、螺钉和螺柱 - 特殊要求
GB /T 3103.1 - 2002
紧固件公差（螺栓、螺柱、螺钉和螺母）
GB /T 34632 - 2017
统一螺纹搓制和滚制前的毛坯直径
GB /T 18685 - 2017
普通螺纹搓制和滚制前的毛坯直径
GB /T 3105 - 2002
普通螺栓和螺钉 - 头下圆角半径
GB /T 5279.2 - 1997
沉头螺钉 第2部分 十字槽插入深度
GB /T 197 - 2018
普通螺纹 公差
类似标准及供货信息
1 开槽沉头螺钉 [国标]
GB /T 68 - 2016		 开槽沉头螺钉
Slotted Countersunk Flat Head Screws
供应商(5)
2 开槽沉头螺钉 [国标]
GB /T 68 - 2000		 开槽沉头螺钉
Slotted Countersunk Head Screws (Commen Head Style)
供应商(5)
3 开槽沉头螺钉 [国标]
GB 68 - 1985		 开槽沉头螺钉
Slotted Countersunk Head Screws
供应商(5)
4 开槽沉头不脱出螺钉 [国标]
GB 948 - 1988		 开槽沉头不脱出螺钉
Slotted Countersunk Head Screws With Waisted Shank
5 米制开槽沉头机械螺钉 Table 2 [美标]
IFI 513 - 1982		 米制开槽沉头机械螺钉 Table 2
Metric Slotted Flat Countersunk Head Machine Screws
6 开槽沉头螺钉 [德标]
DIN 963 - 1990		 开槽沉头螺钉
Slotted Countersunk Head Screws
供应商(3)
7 钢结构栓连接用开槽沉头螺钉 [德标]
DIN 7969 - 1989		 钢结构栓连接用开槽沉头螺钉
Slotted countersunk head screws for structural steel bolting for supply with or without nuts
8 开槽沉头（平头）螺钉 - 适用于精密机械；M0.4至M1.4 [德标]
DIN 8245 - 1972		 开槽沉头（平头）螺钉 - 适用于精密机械；M0.4至M1.4
Slotted Countersunk (Flat) Head Screws for Fine Mechanics; M 0.4 to M 1.4
9 开槽沉头螺钉（通用头型） - 产品等级A级 [国际]
ISO 2009 - 2011		 开槽沉头螺钉（通用头型） - 产品等级A级
Slotted Countersunk Flat Head Screws (Common Head Style) - Product Grade A
10 开槽沉头螺钉（通用头型） - 产品等级A级 [国际]
ISO 2009 - 1994		 开槽沉头螺钉（通用头型） - 产品等级A级
Slotted Countersunk Flat Head Screws (common Head Style) - Product Grade A
11 开槽沉头螺钉 表8 [日标]
JIS B 1101 - 2017		 开槽沉头螺钉 表8
Slotted Countersunk Head Screws - Table 8
12 开槽沉头螺钉 附表JA.4 [日标]
JIS B 1101 (JA4) - 2017		 开槽沉头螺钉 附表JA.4
Slotted Countersunk Head Screws - Table JA.4
13 精密机械用开槽沉头螺钉 [日标]
JIS B 1116 - 2009		 精密机械用开槽沉头螺钉
Slotting Countersunk Head Screws For Fine Mechanics
14 开槽沉头螺钉 附表2 [Annex Attached Table 2] [日标]
JIS B 1101 (AAT2) - 1996		 开槽沉头螺钉 附表2 [Annex Attached Table 2]
Slotted Countersunk Head Screws [Annex Attached Table 2]
15 开槽沉头螺钉 [Attached Table 3] [日标]
JIS B 1101 - 1996		 开槽沉头螺钉 [Attached Table 3]
Slotted Countersunk Head Screws [Attached Table 3]
16 开槽沉头螺钉 (精制) [日标]
JIS B 1179 - 1994		 开槽沉头螺钉 (精制)
Slotted Flat Head Bolts, Fine Finished
17 开槽沉头螺钉 (粗制） [日标]
JIS B 1179 - 1994		 开槽沉头螺钉 (粗制）
Slotted Flat Head Bolts, Rough Finished
18 80°开槽沉头螺钉Table1 [美标]
ASME/ANSI B 18.6.3 - 2010		 80°开槽沉头螺钉Table1
80° Slotted flat countersunk head machine screws
19 100°开槽沉头螺钉Table3 [美标]
ASME/ANSI B 18.6.3 - 2010		 100°开槽沉头螺钉Table3
Slotted 100 deg flat countersunk head screws (machine screws only)
20 紧公差100°开槽沉头螺钉Table5 [美标]
ASME/ANSI B 18.6.3 - 2010		 紧公差100°开槽沉头螺钉Table5
Close Tolerance 100 Degree Slotted Countersunk Head Screws
21 80°开槽沉头清根螺钉Table9 [美标]
ASME/ANSI B 18.6.3 - 2010		 80°开槽沉头清根螺钉Table9
80° Slotted undercut 82-deg flat countersunk head machine screws
22 开槽沉头螺钉 [Table 1] (A307, SAE J429, F468, F593) [美标]
ASME/ANSI B 18.6.2 - 1998 (R2010)		 开槽沉头螺钉 [Table 1] (A307, SAE J429, F468, F593)
Slotted Flat Countersunk Head Cap Screws [Table 1] (A307, SAE J429, F468, F593)
23 米制开槽沉头螺钉Table2 [美标]
ASME/ANSI B 18.6.7M - 1998		 米制开槽沉头螺钉Table2
Metric soltted countersunk screws
24 开槽100°沉头小螺钉 [Table 3] [美标]
ASME/ANSI B 18.11 - 1961 (R1983)		 开槽100°沉头小螺钉 [Table 3]
Slotted 100°flat head miniature screws
25 开槽沉头螺钉 [意大利]
UNI 6109		 开槽沉头螺钉
Slotted countersunk flat head screws
26 开槽沉头螺钉 [法国]
NF E 25-123 - 1994		 开槽沉头螺钉
Slotted Countersunk Flat Head Screws - Product Grade A
27 铁路车辆 沉头侧切口机械螺钉 [法国]
NF F 03-004 (F) - 1983		 铁路车辆 沉头侧切口机械螺钉
Railway rolling stock Grade A Countersunk notched head machine
28 铁路车辆 开槽沉头螺钉/螺母 A级 符号FP [法国]
NF F 03-016 - 1983		 铁路车辆 开槽沉头螺钉/螺母 A级 符号FP
Railway rolling stock Grade A Slotted countersunk head screws nuts Symbol FP
29 开槽沉头螺钉（短的）Table 6 [英标]
BS 1981 - 1991		 开槽沉头螺钉（短的）Table 6
Slotted Truncated Countersunk Head Screws: Short Length
30 开槽沉头螺钉Table4 [英标]
BS 1981 - 1991		 开槽沉头螺钉Table4
Slotted Countersunk Flat Head Screws
31 开槽沉头机械螺钉 [英标]
BS 4183 (T2) - 1967		 开槽沉头机械螺钉
Slotted countersunk head machine screws. Metric series
32 英制开槽沉头螺钉 - B.S.W. & B.S.F. 螺纹 [Table 2] [英标]
BS 450 - 1958		 英制开槽沉头螺钉 - B.S.W. & B.S.F. 螺纹 [Table 2]
Slotted 90°Countersunk Head Screws with B.S.W. & B.S.F. Threads [Table 2]
33 米制开槽沉头螺钉 [Table 1] [澳标]
AS /NZS 1427 - 1996		 米制开槽沉头螺钉 [Table 1]
ISO metric slotted countersunk head screws [Table 1]
34 精密机械用开槽沉头螺钉 [台湾]
CNS 9678 - 1982		 精密机械用开槽沉头螺钉
Slotted Countersunk Screws For Fine Mechanics
35 开槽沉头螺钉 [台湾]
CNS 4411 - 1981		 开槽沉头螺钉
Slotted Countersunk Head Screws
36 开槽沉头螺栓 [台湾]
CNS 4420 - 1981		 开槽沉头螺栓
Slotted Countersunk Head Bolts
37 精密用开槽沉头螺钉 M0.4～M1.4 [台湾]
CNS 4363 - 1980		 精密用开槽沉头螺钉 M0.4～M1.4
Slotted Countersunk Head Screws For Fine Mechanics
38 开槽沉头螺钉 A级和B级 [俄标]
GOST 17475 - 1980		 开槽沉头螺钉 A级和B级
Countersunk head screws of accuracy classes A and B（Slotted）
39 开槽沉头螺钉【Table 5】 [韩标]
KS B 1021 (T5) - 2012 (R2022)		 开槽沉头螺钉【Table 5】
Slotted Countersunk Flat Head Screws【Table 5】
40 开槽沉头螺钉(通用头型) A级 [德标]
DIN EN ISO 2009 - 2011		 开槽沉头螺钉(通用头型) A级
Slotted Countersunk Flat Head Screws(Common Head Style)-Product Grade A
供应商(3)
41 光杆公差带f9 100°沉头螺栓 [军标]
GJB 3371 (/61) - 1998		 光杆公差带f9 100°沉头螺栓
100° Countersunk Head Bolts，Shank Tolerance f9
42 100°沉头不脱出螺钉 [军标]
GJB 3372 (/56) - 1998		 100°沉头不脱出螺钉
Slotted 100 deg flat countersunk head screws, Waisted shank
43 开槽沉头螺钉（通用头型） - 产品等级A级 [印标]
IS 1365 - 2005		 开槽沉头螺钉（通用头型） - 产品等级A级
Slotted Countersunk Flat Head Screws (common Head Style) - Product Grade A
44 开槽100°沉头小螺钉 [Table 3] (A276, B16, B151) [美标]
ANSI B 18.11 - 1961 (R2017)		 开槽100°沉头小螺钉 [Table 3] (A276, B16, B151)
Slotted 100°Flat Head Miniature Screws [Table 3] (A276, B16, B151)
45 82°开槽沉头机械螺钉 [Table 1] (ASTM F837 / F468) [美标]
ASME B 18.6.3 (T1) - 2013		 82°开槽沉头机械螺钉 [Table 1] (ASTM F837 / F468)
82° Slotted Flat Countersunk Head Machine Screws [Table 1] (ASTM F837 / F468)
46 100°沉头开槽机械螺钉 [Table 3] (ASTM F837 / F468) [美标]
ASME B 18.6.3 (T3) - 2013		 100°沉头开槽机械螺钉 [Table 3] (ASTM F837 / F468)
Dimensions of Slotted 100-deg Flat Countersunk Head Screws [Table 3] (ASTM F837 / F468)
47 开槽精密100°沉头机械螺钉 [Table 5] (ASTM F837 / F468) [美标]
ASME B 18.6.3 (T5) - 2013		 开槽精密100°沉头机械螺钉 [Table 5] (ASTM F837 / F468)
Dimensions of Slotted Close Tolerance 100-deg Flat Countersunk Head Screws (Machine Screws Only) (ASTM F837 / F468)
48 开槽82°沉头清根机械螺钉 [ Table 9 ] (ASTM F837 / F468) [美标]
ASME B 18.6.3 (T9) - 2013		 开槽82°沉头清根机械螺钉 [ Table 9 ] (ASTM F837 / F468)
Dimensions of Undercut 82-deg Flat Countersunk Head machine Screws (ASTM F837 / F468)
49 开槽沉头螺栓 [航天]
QJ 2370 - 1992		 开槽沉头螺栓
Slotted countersunk head screws
50 开槽沉头螺钉 [航天]
QJ 2373 - 1992		 开槽沉头螺钉
Slotted countersunk head screws
51 100°开槽沉头螺钉 [航空]
HB 7187~7195 - 1995		 100°开槽沉头螺钉
100° Countersunk Head Bolts
52 100°开槽沉头螺钉 [航空]
HB 7208~7216 - 1995		 100°开槽沉头螺钉
Slotted 100 deg flat countersunk head screws
注：技术数据仅供参考，以官方原件为准！
© 易紧通 服务热线：4006-164580（免长途费）