GB /T 1563 - 2017
Taper keys of keyways
GB /T 6188 - 2017
Hexalobular internal driving feature for bolts and screws
GB /T 2 - 2016
Fasteners-Ends of parts with external thread（ISO 4753:2011, MOD）
GB /T 3106 - 2016
Fasteners - Bolts, screws and studs - Nominal lengths and thread lengths (ISO 888:2012, MOD)
GB /T 152.2 - 2014
Countersinks for countersunk head screws
GB /T 13807.1 - 2008
Connections with waisted stud - Tape classification
GB /T 5652 - 2008
Flared couplings - Flared end
GB /T 6188 - 2008
Hexalobular internal driving feature for bolts and screws
GB /T 6403.3 - 2008
Knurl
GB /T 20330 - 2006
Drill diameter for use prior to tapping screw threads
GB /T 1095 - 2003
Square and rectangular keyways
GB /T 1098 - 2003
Woodruff keyways
GB /T 3105 - 2002
General purpose bolts and screws - Radius under the head
GB /T 145 - 2001
Center holes
GB 18194 - 2000
Rivet shank diameters (except blind rivets)【ISO 1051:1999】
GB /T 16823.1 - 1997
Stress area and bearing area for threaded fasteners
GB /T 5279.2 - 1997
Countersunk flat head screws - Part2: Penetration depth of cross recesses
GB /T 12520 - 1990
Offset cruciform recess fro rotary fastening devices
GB 152.1 - 1988
Clearance holes for rivets
GB 707 - 1988
Hot-rolled channel steel
GB 6189 - 1986
Hexagon lobuar for fasteners - Type E
GB 5277 - 1985
Fasteners - Clearanc holes for bolts and screws
GB 5278 - 1985
Fasteners - Split pin holes and wire holes （ISO 7378:1983）
GB /T 5279 - 1985
Countersunk head screws - Head configuration and gauging
GB 944.1 - 1985
Cross recesses for screws
GB 3104 - 1982
Fastners - Widths across flats of hexagon products
GB 3105 - 1982 (R1988)
DIN 7500 (-2) - 2016
Self-tapping screws for metric ISO threads - Part 2: Guide values for hole diameters
DIN 76-1 - 2016
Thread run-outs and thread undercuts
DIN 7975 - 2016
Tapping screw connections - Guideline values for core hole diameters and use
DIN 332 (-1) - 1986
60° centre holes - Types R. A. B. and C
DIN 7500-2 - 1984
Thread rolling screws for ISO metric thread guidelinge values for hole diameters
DIN 78 - 1983
Thread ends and lengths of projection of bolt ends for metric ISO threads according to DIN 13
DIN 82 - 1973
Knurle
ISO 6149-1 - 2022
Connections for hydraulic fluid power and general use - Ports and stud ends with ISO 261 metric threads and O-ring sealing - Part 1: Ports with truncated housing for O-ring
ISO 10664 - 2014
Hexalobular internal driving feature for bolts and screws
ISO 1179-1 - 2013
Connections for general use and fluid power - Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing - Part 1: Threaded ports
ISO 13444 - 2012
Dimensioning and indication of knurling
ISO 4753 - 2011
Fasteners—Ends of parts with external ISO metric thread
ISO 1179-4 - 2007
Connections for general use and fluid power - Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing - Part 4: Stud ends for general use only with metal-to-metal sealing (type B)
ISO 10664 - 2005
Hexalobular internal driving feature for bolts and screws
ISO 1302 - 2002
Geometrical product specifications (GPS) - Indication of surface texture in technical product documentation
ISO 1051 - 1999
Rivet shank diameters
ISO 7403 - 1998
Aerospace - Spline drives - Wrenching configuration - Metric series
ISO 9974-1 - 1996
Connections for general use and fluid power - Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing - Part 1: Threaded ports
ISO 9974-2 - 1996
Connections for general use and fluid power - Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing - Part 2: Stud ends with elastomeric sealing (type E)
ISO 9974-3 - 1996
Connections for general use and fluid power - Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing - Part 3: Stud ends with metal-to-metal sealing (type B)
ISO 11926-3 - 1995
Connections for general use and fluid power - Ports and stud ends with ISO 725 threads and O-ring sealing - Part 3: Light-duty (L series) stud ends
ISO 6157-2 - 1995
Fasteners—Surface discontinuities— Part2:Nuts
ISO 7721-2 - 1990
Countersunk flat hed screws—Part 2:Penetration depth of cross recesses
ISO 6157-1 - 1988
Fasteners—Surface discontinuities— Part1:Bolts,screws and studs for general requirements
ISO 6157-3 - 1988
Fasteners—Surface discontinuities— Part3:Bolts,screw and studs for special requirements
ISO 7994 - 1985
Internal drive, offset cruciform recess (Torq-Set) for rotary fastening devices. Metric series
ISO 4755 - 1983
Fasteners—Thread undercuts for external metric ISO
ISO 4757 - 1983
Cross recessed-H type
ISO 4757 - 1983
Cross recessed-Z type
ISO 7378 - 1983
Fasteners—Bolts,screws and studs—Split pins holes and wire holes
ISO 7721 - 1983
Countersunk head screws—Head configuration and guaging
ISO 272 - 1982
Fasteners—Hexagon products—Widths across flats
ISO 273 - 1979
Fasteners─Clearance holes for bolts and screws
ISO 3508 - 1976
Thread run-out for fasteners with thread in accordance with ISO 261 and ISO 262
ISO 274 - 1975
Copper tubes of circular section - Dimensions
JIS B 1015 - 2018
Hexalobular internal driving feature for bolts and screws
JIS B 1603 - 1995
Straight cylindrical involute splines -- side fit -- Generalities, dimensions and inspection
JIS B 1215 (T6) - 1976
length of semi-tubular rivets
JB /T 4024 - 2014
Automatic Cold Header - Hole Size
JB /T 9157 - 2011
Hydraulic fluid power-Ball expansion type plug - Mounting dimensions
JB /ZQ 4247 - 2006
JB /T 6960 - 1993
ASME/ANSI B 18.6.3 (T2) - 2013
Recess Dimensions for Flat 82° Countersunk Head Screws
ASME/ANSI B 18.6.3 (T4) - 2013
Recess Dimensions for 100-deg Flat Countersunk Head Screws (Machine Screws Only)
ASME/ANSI B 18.6.3 (T6) - 2013
Recess Dimensions for Close Tolerance 100-deg Flat Countersunk Head Screws (Machine Screws Only)
ASME/ANSI B 18.6.3 (T8) - 2013
Recess Dimensions for Oval 82° Countersunk Head Screws
ASME/ANSI B 18.6.3 (T10) - 2013
Recess Dimensions for Undercut 82-deg Flat Countersunk Head Screws
ASME/ANSI B 18.6.3 (T12) - 2013
Recess Dimensions for Undercut Oval 82-deg Countersunk Head Screws
ASME/ANSI B 18.6.3 (T14) - 2013
Recess dimensions for Flat Countersunk Trim Head Screws
ASME/ANSI B 18.6.3 (T16) - 2013
Recess Dimensions for Oval 82-deg Coutersunk Trim Head Screws
ASME/ANSI B 18.6.3 (T19) - 2013
Recess Dimensions for Pan Head Screws (Types IA, III, and VI)
ASME/ANSI B 18.6.3 (T22) - 2013
Recess Dimensions for Fillister Head Screws
ASME/ANSI B 18.6.3 (T25) - 2013
Recess Dimensions for Truss Head Screws
ASME/ANSI B 18.6.3 (T26) - 2013
Dimensions of Combination Slotted Truss Head Screws
ASME/ANSI B 18.6.3 (T28) - 2013
Recess Dimensions for Binding Head Screws (Machine Screws Only)
ASME/ANSI B 18.6.3 (T30) - 2013
Recess Dimensions for Indented Regular and Large Hex Head Screws
ASME/ANSI B 18.6.3 (T31) - 2013
Recess Dimensions for Type I Nonindented Regular and Large Hex Head Screws
ASME/ANSI B 18.6.3 (T33) - 2013
Recess Dimensions for Indented Hex Washer Head Screws
ASME/ANSI B 18.6.3 (T34) - 2013
Recess Dimensions for Combination Slotted Type I Indented Hex Washer Head Screws
ASME/ANSI B 18.6.3 (T36) - 2013
Recess Dimensions for Round Head Screws
ASME/ANSI B 18.6.3 (T37) - 2013
Recess Dimensions for Combination Slotted Round Head Screws
ASME/ANSI B 18.6.3 (T39) - 2013
Recess Dimensions for Round Washer Head Screws
ASME/ANSI B 18.6.3 (T43) - 2013
Dimensions of Threads and Points for Types BF and BT Thread-Cutting Tapping Screws
ASME/ANSI B 18.6.3 (T44) - 2013
Dimensions of Threads and Points for Type D, F, G, and T Thread-Cutting Tapping Screws
ASME/ANSI B 18.6.3 (T45) - 2013
Dimensions of Type TRS Tapping Screws
ASME/ANSI B 18.6.3 (T46) - 2013
Thread Lengths for Type A, AB, B, BF, BP and BT Tapping Screws
ASME/ANSI B 18.6.3 (T47) - 2013
Thread Lengths for Type C, D, F, G, T and TRS Tapping Screws
ASME/ANSI B 18.6.3 (T48) - 2013
Standard Test-Plate Thickness and Hole Sizes for Drive-Test Inspection of Tapping Screws
ASME/ANSI B 18.6.3 - 2010
ASME/ANSI B 18.6.3 - 2010
ASME/ANSI B 18.17 - 1968 (R1983)
Dimensions of Alternate Styles of Points for Thumb and Wing Screws
EN 10058 - 2018
Hot rolled flat steel bars and steel wide flats for general purposes - Dimensions and tolerances on shape and dimensions
EN 27721 - 1991
Countersunk head screws - Head configuration and gauging
