六角头自攻螺钉和平垫组合 DIN EN ISO 10510 (S1) - 2011
| 选择规格尺寸 点击↓ ST2.2 ST2.9 ST3.5 ST4.2 ST4.8 ST5.5 ST6.3 ST8 ST9.5 |
尺寸单位:
mm |
|
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| ①,作为组合自攻螺钉的组件的螺钉的机械性能必须符合ISO 2702的要求。在组装和热处理之后，垫片必须具有90HV到320HV的硬度。 维氏硬度试验必须根据ISO 6507-1进行。 试验载荷：HV 10，标称厚度h~1,2 mm 试验载荷：HV 30，标称厚度h> 1,2 mm 在组装之前，必须采取适当的预防措施 ②,螺钉的名称和代号 ISO 1479，六角自攻螺钉，S1 ③,垫片的名称和代号： ISO 10669，平垫圈 - 用于组合自攻螺钉，标准型 N，加大型 L |
采用标准
类似标准及供货信息
| 1 |
|
[国标] GB /T 9074.20 - 2004 |
十字槽凹穴六角头自攻螺钉和平垫圈组合件 Cross Recessed Hexagon Head Tapping Screw With Indentation And Washer Assemblies With Plain Washers 供应商(3) |
| 2 |
|
[国标] GB /T 9074.20 - 1988 |
十字槽凹穴六角头自攻螺钉和平垫组合 Cross Recessed Hexagon Head Tapping Screw With Indentation And Plain Washer Assemblies 供应商(3) |
| 3 |
|
[国标] GB 9074.21 - 1988 |
十字槽凹穴六角头自攻螺钉和大平垫组合 Cross Recessed Hexagon Head Tapping Screw With Indentation And Large Plain Washer Assemblies 供应商(3) |
| 4 |
|
[国标] GB 9074.22 - 1988 |
六角头自攻螺钉和平垫圈组合 Hexagon Head Tapping Screw And Plain Washer Assemblies 供应商(1) |
| 5 |
|
[国标] GB 9074.23 - 1988 |
六角头自攻螺钉和大垫圈组合件 Hexagon Head Tapping Screw And Plain Washer Assemblies 供应商(1) |
| 6 |
|
[国标] GB /T 9074.18 (S1) - 2017 |
六角头自攻螺钉和平垫组合 Hexagon Head Tapping Screws And Plain Washer Assemblies |
| 7 |
|
[国标] GB /T 9074.18 (S1) - 2002 |
六角头自攻螺钉和平垫组合 Hexagon Head Tapping Screws And Plain Washer Assemblies |
| 8 |
|
[国际] ISO 10510 (S1) - 2011 |
六角头自攻螺钉和平垫组合 Hexagon Head Tapping Screw With Plain Washers |
| 9 |
|
[国际] ISO 10510 (S1) - 1999 |
六角头自攻螺钉和平垫组合 Hexagon Head Tapping Screw With Plain Washers |
| 10 |
|
[日标] JIS B 1129 - 2004 |
六角头自攻螺钉和平垫组合 Hexagon Head Tapping Screws And Plain Washesr Assemblies 供应商(1) |
| 11 |
|
[日标] JIS B 1129 - 1999 |
六角头自攻螺钉和平垫组合 Hexagon head tapping screw and plain washer assemblies 供应商(1) |
| 12 |
![米制六角头平尾自攻钉和弹垫组合件 SEMS[Table 2]](http://img.164580.com/upload/48/pic/2022/01/24/1642999444706032512.jpg)
|
[美标] ASME/ANSI B 18.13.1M - 2011 |
米制六角头平尾自攻钉和弹垫组合件 SEMS[Table 2] Metric Hexagon Head Tapping Screws and Spring Washer Assemblies-SEMS (Screws Having Tapping Screw Thread Diameter) |
| 13 |
|
[法国] NF E 25-523 - 1999 |
六角头自攻螺钉和平垫组合 Hexagon Head Tapping Screw And Washer Assemblies With Plain Washers |
| 14 |
|
[原电子工业部] SJ 2840 - 1987 |
十字槽六角头自攻钉和平垫圈组合 |
| 15 |
|
[美标] ASME B 18.13 - 2017 |
六角头自攻螺钉和弹垫组合 SEMS[Table 3] Hex Head Tapping Screw and Spring Washer Assemblies-SEMS (Type B Tapping Screw Thread Diameter) |
注：技术数据仅供参考，以官方原件为准！
© 易紧通 服务热线：4006-164580（免长途费）